This project has as main goal to study the influence of the coating thickness, deposited by arc-PVD- technology, on the wear resistance of coated cemented carbide inserts in three different turning operations. An additional effort has also been made to develop a new test method for evaluating flank wear resistance. Three different coating types (Coating A, Coating B and Coating C) have been studied in three distinctive thicknesses (2, 4 and 6 µm) for each type. For two of the coating types (Coating A and B) special studies has been done with the thickest coating, creating two additional coating versions of the thickest coating, by changing various deposition parameters, with the aim to enhance the cohesive properties of the coating and lower the residual stresses at the cutting edge. The results show increased crater wear resistance with increased coating thickness for all coating types, but the amount of increase changes with coating type (Coating A>B>C).

By our employer Camatec Industriteknik AB have we been given the assignment to continue with the previous work ?Design of strip feeder?. Our goal with this work is to come up with a design basis for a strip feeder.Functionally a strip feeder consists of two rollers which with the aid of the friction between the strip and the coating on the roller create a strip force that pulls the strip through the working progress.Demands on this project:? 10 ? 600 mm in strip width and 0,1-1 mm in strip thickness.? Minimum 30m/min in production speed.? A maximum strip force on 30-40 kN.? The cost of the strip feeder?s components is to be considered of economy and quality.The need of a strip feeder occurs when the coil doesn?t manage to feed or pull the strip before or after a working process. The strip can otherwise be exposed by a permanent yield deformation or a change in the strip material if it?s pulled trough the working process only by the on ? and of-coils.

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

The development of defoaming additives is steadily progressing and there are therefore always new and improved additives on the market. Some modern additives provide the desired defoaming effects by themselves, in contrasts to previous additives that needed to be used in combination with other additives. The task of this bachelors thesis was to evaluate the possibility of using these improved defoaming additives, with the aim to find alternatives that give the system better defoaming attributes while, at the same time, using less of the primary products. The tests were carried out in the coating type Teknocryl Aqua Combi 2780. The coating is a waterborne air drying acrylat-latex/alkyd based coating that can be used for both single coat painting and primer.

Steel is an excellent material to build with, but consideration must be given to the fact that unprotected steel corrodes, rusts, therefore, as a rule, the steel must be protected in some way. This can be done by reducing the tendency of the steel to corrode by using stainless steel or by treating the steel with a protection method. The two most common methods of protection are corrosion protection paint and zinc coating. To determine the method, the corrosive category must first be evaluated and this is done in accordance to EN ISO 12944-2:1998.Stainless steel is available in many varieties but only some of them have properties that make them suitable for use as construction steels. There are many factors to be considered in the design of stainless steel to prevent corrosion from occurring.

Introduction: Studies have shown that women are not always satisfied with the effects of contraception and that contraceptive advice is perceived as non-specific. Aim: The purpose of this study was to investigate what contraceptive women have chosen to use in the different phases of their reproductive lives, and what they felt had influenced their choice. Method: A retrospective cross-sectional comparative study with a quantitative approach. A survey with fixed and multiple-choice options was sent to five hundred 45-year old women. Result: The study shows that various birth controls are different in the normal reproductive life.

For several years Uppsala University together with several companies has been involved in a WISENET project aimed at improving railway transport security. By placing a sensor system near the wheels of each wagon, the temperature of the bearings can be measured and transmitted to a collector placed centrally on the wagon. This in turn transmits the collected data to RFID receivers placed intermittently along the railway.As the signals are transmitted wirelessly, problems may occur as the antennas get dirty or coated with ice and snow. To determine the effects of these coatings, several tests were performed examining the reflection coefficient S11, the impedance Z11 and the efficiency eta of an antenna, and how they varied when various coatings were placed over the antenna. Examined coatings were ice, snow and water to determine the effects of weather, and various metal-based coatings: powdered iron both pure and partially oxidized, and iron ore granules.

The project has been oriented for development of fixtures to ateljé Lyktan to provide a more efficiency line. In the year 2012 the company invested in a new coating booth, which leads to opportunities to upgrading the fixtures and also new design. The request is to minimize the area for storage of fixtures, and therefore should fixtures be designed to apply as many articles as possible The priority of products that fixtures have development to has been products that are most frequently coated and new products that don?t have any fixtures. The product families that the project has been having focus on is TIME and FOVEA with RONDO.

This thesis is about developing a design that provides improved vacuum seal between a lead coating and a plastic coating during plastic extrusion processes of cables. This report is a part of the course MSGC 17 for Bachelor Engineers in mechanical engineering.The work is performed at Nexans Norway AS in Halden where they have a production of high voltage cables for sea-, and offshore industry. A problem they face is that they do not get enough good seal at the attachment to the plastic extrusion machine. They want to achieve a vacuum between a lead coating on the cable and a plastic coating of the cable for plastic extrusion, which is something they do not achieve today. The thesis is thus to come up with a design that provides better sealing against the cable.The work involves a construction part with the phases of product development processes.

The project has been oriented for development of fixtures to ateljé Lyktan to provide a more efficiency line. In the year 2012 the company invested in a new coating booth, which leads to opportunities to upgrading the fixtures and also new design. The request is to minimize the area for storage of fixtures, and therefore should fixtures be designed to apply as many articles as possible The priority of products that fixtures have development to has been products that are most frequently coated and new products that don?t have any fixtures. The product families that the project has been having focus on is TIME and FOVEA with RONDO. In the developing of fixtures have ideas been discussed with the staff, and instructions were made about how you are suppose to hang up the different products.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

The thesis evaluates a new kind of bearing arrangement in a traction motor that ABB hasdeveloped. Since the arrangement is designed in a new and innovative way it needs to beevaluated to see if it is safe to use. In today?s traction motors, bearings with a big internalclearance (C4-clearance) are used. The basic idea of the new arrangement is to reduce the fitsbetween the bearing and shaft/house.

The aim of my thesis was to do a Life Cycle Assessment (LCA) of an average thread tap that is manufactured by Dormer Tools AB, and to create a practical model that the company can use in order to study other thread taps from an environmental perspective.The method of LCA is used to investigate the environmental effects of a product during its life cycle. This is a gate-to-grave analysis with focus on steel and thread tap manufacturing, coating procedure, use, waste management and transports. Three common coating types were compared separately. Steel manufacturing answers for the highest energy and raw material consumption under the life cycle of the thread tap. Its emissions contribute to global warming, acidification and eutrophication above others.